2013 Jeep Wrangler

2013 Jeep Wrangler, which is currently subject to a manufacturer-issued “Do Not Drive” safety recall involving the driver’s airbag. Upon learning of the recall, I immediately acted responsibly by delivering my vehicle to Romano Chrysler Jeep in Fayetteville, New York, so the required safety repair could be completed. My Jeep has now been at the dealership for more than six weeks because the replacement airbag remains on backorder. During this time, I have repeatedly requested updates and asked whether a loaner or rental vehicle could be provided. Despite the fact that Stellantis has instructed owners not to drive affected vehicles, I have been informed that no transportation assistance will be provided. Compounding the problem, my New York State inspection expired while the Jeep has been sitting at the dealership. I attempted to have the vehicle inspected before bringing it in, but was advised that it could not legally be inspected until the safety recall had been completed. As a result, I have been left without a usable vehicle through no fault of my own. I fully understand that supply chain delays and backordered parts can occur. However, I do not believe it is reasonable or fair for a consumer to bear the financial and personal burden of a manufacturer-issued Do Not Drive recall while the required repair cannot be completed. As a long-time automotive owner, taxpayer, and consumer, I believe manufacturers should stand behind their products when a federally mandated safety recall removes a customer’s ability to safely operate their vehicle. I respectfully request the following: Immediate authorization for a loaner or rental vehicle at Stellantis’ expense until my Jeep is repaired. Expedited shipment of the required replacement airbag, if possible. Written confirmation of Stellantis’ position regarding transportation assistance during this prolonged recall delay.

Reported

Jul 2026

Incident date

Jun 2026

Mileage

Not provided

Outcome flags

None reported

The abs module is providing a code and mechanic states it is defective and needs to be replaced. Manufacturer has no parts available for repair. No accident occurred, only way to use vehicle is without abs protected braking.

Reported

Jul 2026

Incident date

Jul 2026

Mileage

Not provided

Outcome flags

None reported

Had this 2013 Jeep Wrangler since new and has ABS module internal failure code C2200. ABS, ANTI SKID, BRAKE lights are constantly lit on the dashboard. No ABS on this Jeep making it unsafe in an emergency braking situation which could cause a crash. Have tried for over a year and a half to have the ABS repaired or get a new ABS Module. As of today, June 29, 2026, Mopar Parts has again informed us that the ABS Module is unavailable. The Internet has been alive with many Jeep Wrangler owners driving around with no ABS braking. NTSA needs to take action to get this corrected.

Reported

Jun 2026

Incident date

Jan 2024

Mileage

Not provided

Outcome flags

None reported

The ABS module failed in summer 2025. We took the Jeep to the mechanic who was unable to source a new part. The part has been on backorder now for over a year. We cannot get the Jeep inspected because of the break safety issue. The Jeep has no ABS if emergency breaking. Several warning lights are constantly on when operating the Jeep.

Reported

Jun 2026

Incident date

Jun 2025

Mileage

Not provided

Outcome flags

None reported

2013 Jeep Wrangler. ABS module internal failure code C2200. 3 lights are constantly lit on the dashboard. No ABS on this Jeep, making it unsafe in the rain and snow. No way to have this part repaired anymore, nor does the dealership offer it. Shameful and shocking that MOPAR isn't dealing with this problem. Many, many Jeep owners are dealing with this problem. When will we see a recall??

Reported

May 2026

Incident date

May 2026

Mileage

Not provided

Outcome flags

None reported

C2200 Abs control module internal failure. Anti lock brake, traction control stop working. Vehicle can go into limp mode and not be drivable. Apparently due to safety concerns replacment parts are not produced by the manufacturer. This causing the vehilce to not be driven safely.

Reported

May 2026

Incident date

May 2026

Mileage

Not provided

Outcome flags

None reported

I purchased a 2013 Jeep Wrangler Unlimited Sahara (VIN [XXX] ) from Soliman Motors Inc., [XXX] (phone [XXX] ) on April 11, 2026. The vehicle is subject to active NHTSA stop-drive recall #19V-018 for the Takata passenger airbag inflator, issued January 15, 2019. This recall was not disclosed to me at any point before, during, or after the purchase. I was never informed of this active federal stop-drive safety recall by the dealer. I discovered the recall independently after purchase through the Jeep manufacturer app. Upon discovery I immediately contacted an authorized Jeep dealership to schedule the recall repair. I was informed that recall parts are on nationwide backorder with no confirmed availability date. I am currently on a waiting list at an authorized Jeep dealership. This recall has been open and unrepaired for over seven years since its issuance on January 15, 2019. The dealer sold this vehicle to me without disclosing the existence of this active stop-drive safety recall. The recall involves a Takata passenger airbag inflator that can rupture upon deployment, sending metal shrapnel toward vehicle occupants — a known life-threatening defect responsible for deaths and serious injuries worldwide. I have been driving this vehicle without any knowledge of this life-threatening safety defect from the date of purchase until I independently discovered the recall. The dealer’s failure to disclose this recall at the point of sale put my life and the lives of my passengers at serious risk. Additionally, the financing for this transaction was cancelled by the lender, Thrift Investment Corporation, because the dealer sold this vehicle to a buyer without a valid driver’s license — confirming the dealer failed to conduct basic due diligence before completing this sale. I am requesting: 1.Investigation of Soliman Motors Inc. for failure to disclose active stop-drive recall #19V-018 at point of sale 2.Review of whether Solim INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Reported

May 2026

Incident date

Apr 2026

Mileage

Not provided

Outcome flags

None reported

The ABS module has failed. The jeep was not involved in an accident, it is at my house not driveable because Jeep does not have the ABS module. The part has been on factory back order with no date of availability. No aftermarket company produces the past. I now have a jeep that is useless. Jeep should be held accountable for availability of the part.

Reported

May 2026

Incident date

Aug 2025

Mileage

Not provided

Outcome flags

None reported

My 2013 RHD jeep wrangler is showing codes B1B02 and B1B06. I took it to jason lewis automotive in sparta tn yesterday. The airbag light is on and the horn does not work. These are the exact same failures identified in safety recall s40. The previous owner of my car got this done in 2021 but the remedy has failed and the safety risk is back. They confirmed that the clockspring is bad and needs replacing. The confirmed the codes and it matches the s40 recall.

Reported

Apr 2026

Incident date

Apr 2026

Mileage

Not provided

Outcome flags

None reported

I have a 2013 Jeep Wrangler with 180,000 miles. I never off road the vehicle, but after driving on a dirt road, the stability control kicked in during a turn. At the start of the next drive after that, there were 3 lights on the dashboard: brake, ABS, stability control. Connecting the JScan app to the vehicle, the ABS module is completely unresponsive and the vehicle gives a C2200 error code. There were no symptoms of this issue before this event. This vehicle is available to be inspected any time. Lack of ABS is a very dangerous safety concern, as neither of my children have ever had to drive a vehicle without ABS. After some research, this seems to be a very common problem. After some age and heat cycles, the electronics in the module become weak, and my single use of the Stability control apparently is enough to push the weak electronics over the edge and destroy the module. This has been confirmed through several companies who repair these modules, such as [XXX] , who no longer repairs these modules, apparently because the computer chips are no longer made, and I have heard stories about the chip maker going out of business during covid. It was also confirmed by a local Jeep specialist, and the dealer parts department also tells the same story, people have been waiting on this module for over 2 years now. A manufacturer of this size with this many vehicles affected by such a safety issue should step up and commission another chip manufacturer to make these vehicles road worthy again. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Reported

Apr 2026

Incident date

Apr 2026

Mileage

Not provided

Outcome flags

None reported

The clockspring went bad, but the recall for that only applies to 2007-2010 Jeep Wranglers. The airbag light is on, my horn does not work, and the buttons on my steering wheel don't work.

Reported

Apr 2026

Incident date

Jan 2026

Mileage

Not provided

Outcome flags

None reported

I have $80,000 in my jeep parked in my garage because the ABS module failed. Error code C2200. I have taken it to three Mechanics; Kap Motor Sports in Palmetto Fl, AFNY, and 4 Wheel Parts in Bradenton Fl. All have run tests coming back with the same error. We have done two Abs bleeds to try and fix the problem. This part should have been recalled years ago. It has been on back order for years and when Firkins Jeep in Bradenton Fl tried to order the part the order was canceled by Jeep. Jeep hasn't recalled it and isn't making it available for their customers who have spent so much money on their jeeps. At this point a lawsuit needs to be filed and have started that process. This is my daily driver and if my Jeep kills or injures someone due to this ABS failure Jeep will be held responsible.

Reported

Apr 2026

Incident date

Feb 2026

Mileage

Not provided

Outcome flags

None reported

The component that failed is the Anti-Lock Braking System (ABS) Control Module in a 2013 Jeep Wrangler. Diagnostic code C2200 (“ABS Control Module Internal Failure”) was retrieved during a scan, indicating an internal electronic failure within the ABS module. The component remains installed in the vehicle and is available for inspection upon request. When the failure occurs, the vehicle’s ABS, traction control, and stability control systems become disabled. The dashboard displays warning lights for the ABS, traction control, and brake system. While the base braking system continues to function, the loss of these electronic safety systems could increase the risk of reduced vehicle control during emergency braking or low-traction conditions such as wet or slippery roads. The issue has been confirmed through diagnostic scanning by a service center, which produced code C2200 indicating an internal failure of the ABS control module. The condition is repeatable: the warning lights appear after approximately 10 minutes of driving, and if the vehicle is turned off and allowed to sit for a period of time (such as overnight), the lights reset but return again after driving. The replacement ABS control module is currently extremely difficult to obtain. According to a Jeep dealership parts department, the module is on significant backorder, with hundreds of outstanding orders that were expected to be filled earlier in 2026 but remain unfulfilled. The part is widely reported within the Jeep owner community to be a common failure for this vehicle generation, yet no recall or official remedy has been issued.

Reported

Mar 2026

Incident date

Feb 2026

Mileage

Not provided

Outcome flags

None reported

ABS anti lock module stopped working. Vehicle braking system is now compromise. It also send the speed to the transmission, which is causing the erratic drivability.

Reported

Mar 2026

Incident date

Dec 2025

Mileage

Not provided

Outcome flags

None reported

The ABS module that controls the antilock braking system is defective for mine and many other Jeeps from 2013-2017. Jeep is no longer manufacturing this part, and essentially this renders the vehicle undriveable. I have sought modules both locally and online, and the experts are telling me that Jeep has not made this part in years. When driving with the bad ABS module while trying to search for the new part, my Jeep shut down on the highway twice, and I was forced to pull over the side of the road. This was extremely dangerous. And Jeep is providing no solutions for owners.

Reported

Mar 2026

Incident date

Jan 2026

Mileage

Not provided

Outcome flags

None reported

The oil filter housing is known to leak, crack or break in standard weather conditions. This can be exacerbated by extreme climate or by simply storing the vehicle outside of a climate controlled area. The hazards posed start with the slow but continuous leak of engine oil from the housing down the transmission and driveline to the ground. This is an environmental hazard to ground water and plant life. The oil can also contaminate roadways leading to slick spots in the road coupled with icy conditions this could cause for large scale vehicular incidents. Lastly if this issue goes unchecked and the oil leaks out of the engine entirely or to a low enough level it could cause the engine to seize in some shape or fashion. This would cause the aforementioned hazards to occur all at once culminating a catastrophic hazard event.

Reported

Feb 2026

Incident date

Dec 2025

Mileage

Not provided

Outcome flags

None reported

NHTSA Recall Number 19V018000 Made appointment at West Knoxville Chrysler Dodge Jeep Ram (530 Kingston Pike, Knoxville, TN 37919) Dealership states they do not have the part, do not know when they will have it. They are refusing to help. They did not inspect the vehicle, or even ask if they could. They really didn't want me there for "recall work".

Reported

Feb 2026

Incident date

Feb 2026

Mileage

Not provided

Outcome flags

None reported

ABS module failure with no rplacement available to replace or fix. affecting braking ang driving as well. transmission stays in lower gears and causing transmission to heat up fluid. been waiting for dealearship to provide replacment item purchase a year ago 2024.

Reported

Feb 2026

Incident date

Aug 2024

Mileage

Not provided

Outcome flags

None reported

ABS, dash lights have come on. BRAKE, ABS, Traction. When needing to do sudden braking on wet road tires lock up and Jeep slides. When asked a dealer I was told that the ABS had an internal fail and that replacements are Not aviable. After researching they can not be found or repaired and was told to buy a used replacement. When one was located they said it was no warranty and that it would most likley fail also because they "all fail". Doing an online search this is a wide spread problem and dealers have no fix.

Reported

Feb 2026

Incident date

Aug 2025

Mileage

Not provided

Outcome flags

None reported

The ABS Module for my 2013 Jeep JK Unlimited is not functioning anymore and the manufacturer discontinued the ABS Module and its chip, not allowing repair services to fix them. So I am stuck driving my Jeep with no ABS brakes and placing the car at risk of driving.

Reported

Feb 2026

Incident date

Sep 2024

Mileage

Not provided

Outcome flags

None reported

My ABS, Brake and Traction Control lights all came on 1 month ago. Error code from shop is C2200 indicating a faulty ABS Module. They cannot find a replacement from any Jeep dealers. My online search also unsuccessful as none of the sites have them in stock. Been told by everyone that there is a national shortage and none are available due to Jeep not making them either anymore or cannot keep up with the demand. Now I cannot drive my Jeep safely and there is no timely help. This is a HUGE issue!

Reported

Feb 2026

Incident date

Jan 2026

Mileage

Not provided

Outcome flags

None reported

The ABS Control Module failed. After checking with the dealer, the part is unavailable unless you agree to pay 4x the price. After further research, blogs, online info, it appears this part is back ordered because of a widespread failure. This is dangerous and should have been recalled. Instead they are releasing small amount of part for the purpose of gouging.

Reported

Jan 2026

Incident date

Jan 2026

Mileage

Not provided

Outcome flags

None reported

ANTILOCK BRAKE CONTROL MODULE FAILED BRAKE LIGHT/ ABS LIGHT/ TRACTION CONTROL LIGHT ON BRAKES SPONGEY- LOW PEDAL-NOT RESPONSIVE-, FRONT & REAR END WOBBLEY-UNSTABLE "UNSAFE TO DRIVE" NATIONAL BACKORDER FOR REPLACEMENT PART- DEALER SAID THEY HAVE BEEN WAITING FOR A YEAR 1/2 ALREADY WITH NO ESTIMATED PARTS REPLACEMENTS. NO WRECKING YARDS HAVE PARTS, AND NOT AVAILABLE ONLINE, AS WELL AS NO ONE CAN REBUILD

Reported

Nov 2025

Incident date

Sep 2025

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated that the ABS warning light was illuminated, and a message indicating that the brake light bulb had failed was displayed even though the bulb was operable. The vehicle was taken to an independent mechanic, where it was diagnosed, and determined that the ABS module had failed and needed to be replaced; however, the part was not available. The contact stated that the mechanic contacted several dealers and was informed that the part was on backorder or had been discontinued. A local dealer also informed the contact that an ETA for the part could be provided, but the part would not be available on the expected date based on past experience. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 95,000.

Reported

Oct 2025

Incident date

Apr 2024

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated that while operating the vehicle, the air bag warning light remained illuminated. The contact was concerned that the air bag might not deploy in a crash. The contact was informed that the VIN was not included in the NHTSA Campaign Number: 18V021000 (Air Bags). The contact stated that the vehicle had experienced the failure listed in the recall. The cause of the failure was not yet determined. The manufacturer and local dealer were not contacted. The failure mileage was 70,450.

Reported

Oct 2025

Incident date

Aug 2025

Mileage

Not provided

Outcome flags

None reported

ABS system has failed and Jeep dealer said the parts are on back order and has been for over a year. Depending on who your speaking to at Stellantis they are either re-engineering the part or they are no longer manufacturing it. While my Jeep still drives, there is a major safety concern due the ABS and traction control being unavailable. There is a whole thread set up online and this problem is affecting many people. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Reported

Sep 2025

Incident date

Jul 2024

Mileage

Not provided

Outcome flags

None reported

Oil pressure sensor failed. Fixed that. Check engine light came back on with battery light. New alternator. Check engine returned for oil pressure sensor. Temp gauge is fine. Changed oil twice within 3 months. When replacing jeep alternator melting of wires to alternator had occurred. This seems to be an issue with this model.

Reported

Aug 2025

Incident date

Aug 2025

Mileage

Not provided

Outcome flags

None reported

My 2013 Jeep Wrangler Rubicon, has a non-functional horn and steering wheel controls, including cruise control and audio buttons, which stopped working in. I suspect a faulty clockspring, as these symptoms match issues in prior Jeep Wrangler recalls for 2007-2012 models (NHTSA campaign 11V528000), where clockspring failures also disabled horns and risked airbag malfunctions. My vehicle shows. This poses a safety risk, as the horn is critical for avoiding collisions. No repairs attempted yet, but similar complaints appear online from other 2013 Wrangler owners. Please investigate for a potential recall.

Reported

Aug 2025

Incident date

Jul 2025

Mileage

Not provided

Outcome flags

None reported

Odometer Fraud. The contact purchased a 2013 Jeep Wrangler. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 60,742 and at the time of registration, it was discovered that the mileage was 62,724.

Reported

Jul 2025

Incident date

Sep 2024

Mileage

Not provided

Outcome flags

None reported

The ABS brake module failed, and apparently this is a pretty widespread issue with this module, and it's near impossible to get a replacement. The ABS, traction control, and brake light are on, as well as throwing several transmission related check engine codes. The car is undriveable.

Reported

May 2025

Incident date

Jan 2025

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated that after her husband had arrived at his destination, upon returning to the vehicle and attempting to start the vehicle, the vehicle failed to restart. The vehicle was eventually able to restart and returned to normal functionality, but the failure became a regular occurrence. The contact stated that the failure seemed to occur after driving the vehicle for longer than 45 minutes to one hour. There were no warning lights illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure Safety Recall J30. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 92,000.

Reported

May 2025

Incident date

May 2025

Mileage

Not provided

Outcome flags

None reported

Jeep Wranglers 2013 has a ABS Module issue that Mopar is not having this part avaialble for replacement. There has been years of backorder on this module and everywhere you go they tell us the same. Mopar has a backorder on these and it has taken at times 2 to 3 years to get them. There has not been a recall knowing this is a known issue with Jeep all over.

Reported

May 2025

Incident date

Apr 2024

Mileage

Not provided

Outcome flags

None reported

Loud rattle noise on start up and ticking sound when running. Also using a little antifreeze. There is no antifreeze leaks.

Reported

Apr 2025

Incident date

Dec 2024

Mileage

Not provided

Outcome flags

None reported

My dash lights went crazy while driving. I couldn't get the vehicle into the correct gear ( automatic transmission) I shut off waited then restarted drove home. After having the codes scaned it shows C2200 code ( faulty brake ABS module) called dealer they had none to sell or buy and told me no time was given to them when or if it would be available. I asked them what's the solution to using my vehicle safely then Park it and don't drive it.. Since then I've found thousands of people just like my situation. How can you build a vehicle and be unable to supply the public with replacement parts to operate as intended and not have a recall or offer a solution to trade off said vehicle. It's definitely a safety issue when a100,000 + owners have the exact same issue and no help In sight.

Reported

Apr 2025

Incident date

Oct 2024

Mileage

Not provided

Outcome flags

None reported

ABS Module Failure and no replacement part available for this vehicle. After researching this issue, it should be a recall based on the highly excessive number of complaints and failures on this part. Has been ongoing for over 4 years and dealership says that Jeep Chrysler is aware of the issue and cannot get the part.

Reported

Mar 2025

Incident date

Feb 2025

Mileage

Not provided

Outcome flags

None reported

This vehicle is notorious for a common issue yet that same issue which has not been recalled is the reason my engine blew on the highway and Jeep has failed to notify owners of this issue or give some sort of reimbursement. My Jeep was cruising just fine when my engine suddenly blew, it was well maintained and taken care of. Despite the great care the oil housing unit which many others have complained about cracked leaking all the oil in a matter of minutes. This essential piece failing and releasing all the oil caused my engine to blow. Jeep is notorious for having a plastic oil housing unit with no heat shield since it is inbetween both engine bays. Having the unit where it is while creating the piece out of plastic seems like a text-book way to have catastrophic failure and further profit off complete engine failure. This material design flaw has now cost me nearly $800 come to find out I need a total engine replacement now which will be around $4000. This is completely unacceptable a vehicle was allowed to be put on the road with such a catastrophic design flaw and physically endangered me when this happened. In the attached files you can see the pooling of oil, I also have official reference from a local auto shop and screenshots of multiple online complaints.

Reported

Mar 2025

Incident date

Jan 2025

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated that while driving 50 MPH, the air bag fault message was displayed. A local dealer was contacted. The vehicle was taken to the dealer and the contact was informed that Chrysler Canada would honor the warranty. The vehicle was diagnosed, and it was determined that the clock spring needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and opened a case. The manufacturer was notified of the failure and transferred the contact to the warranty Headquarters located in Florida. The approximate failure mileage was 140,000.

Reported

Feb 2025

Incident date

Sep 2024

Mileage

Not provided

Outcome flags

None reported

My airbag sensor has been continually toggling on and off for a few months now. I had the car scanned at my service center and the code came up as an issue with my driver seat airbag circuit. In my research on recalls for my year vehicle, there is a recall ~NHTSA Campaign Number 16V28800 ~Components AIR BAGS ~Summary The clock spring assembly may become contaminated with dust and cause the airbag circuit to fail. Although this recall is for right hand drive and my Jeep is left hand drive, it appears it may be the same issue. Please advise as I feel unsafe driving my Jeep and will be taking it next week to service center to have it corrected . Thank you. Awaiting your reply.

Reported

Feb 2025

Incident date

Jun 2024

Mileage

Not provided

Outcome flags

None reported

The components in the N28 / NHTSA 13V-234 recall did exactly what they were recalled for. My check engine light came on a few months back so I brought it to be diagnosed at a parts store and diagnostic scanner listed P codes for possible O2 sensor. I brought my 2013 Jeep Wrangler Sport into a Jeep dealership(#1) in Friday, November 1st, 2024 and upon the first inspection, they found a couple of issues and printed an quote for $127.33, I signed off on that quote. Then another hour or 2 passed by, they brought me a revised quote for over $600, which I was still okay with and signed off to have repaired. Then they offered to bring me home after hours of sitting in the lobby. The next day, I get a link to review the revised inspection and it was over $2400. The engine charge was over $1900 caused by the N28 recall. I asked them to just do the recall because I could not afford it the remaining. Upon looking into forums, documents & diagrams researching online specific to the N28 recall, I reached out to the manufacturer quite a few times by phone and email. I was working with someone who I thought would be helpful, since he suggested I call a different Jeep Dealership (#2) Service Dept. and speak with a mechanic there. I spoke with a mechanic at #2 and sent #1's inspection report, and #2 dealership's mechanic confirmed the issues are connected & caused by the recall. The manufacture's contact (that I thought was more helpful than the ones I spoke with prior) was emailing me. I reported back to the contact on November 14th, 2024 what dealership #2 said and he never responded. I followed up for a response on November 21st, 2024. I still have no response as of January 30th, 2025.

Reported

Jan 2025

Incident date

Jan 2025

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated while the vehicle was parked, the air bag warning light intermittently illuminated. The failure occurred on several different occasions. The vehicle was taken to an independent mechanic to be diagnosed; however, the diagnosis was still pending. The contact researched and was made aware of NHTSA Campaign Number: 16V288000 (Air Bags); however, the VIN was not included. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 167,000.

Reported

Jan 2025

Incident date

Nov 2024

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated while driving at an undisclosed speed, there was an engine misfire, with the check engine warning light illuminated. The vehicle was restarted; however, the failure recurred. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and confirmed that the VIN was not included in TSB: 09-002014 Rev. B (Engine). The approximate failure mileage was 95,000.

Reported

Dec 2024

Incident date

Dec 2024

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated while driving approximately 30 MPH, while depressing the accelerator pedal the vehicle failed to respond. The contact stated that it felt as if the transmission had seized. The contact stated that the RPM was revving however, the vehicle failed to respond. The contact stated there was no warning light illuminated. The contact stated that during a state inspection, the contact was informed that the passenger’s side rear axle shaft seal was leaking. The contact had taken the vehicle to a local dealer; however, the vehicle was not diagnosed or repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 116,000.

Reported

Nov 2024

Incident date

Oct 2024

Mileage

Not provided

Outcome flags

None reported

ABS module has gone bad and Jeep Chrysler dealership has told me that they only have nine parts in the nation to replace it and the engineers are not confident in the replaced part, they won’t know when the part would be available and I was also told that if I continue to drive it I could potentially damage other components of the Jeep Wrangler. I was also told by personal mechanic that I shouldn’t drive it as I don’t not have Anti lock breaks..

Reported

Jul 2024

Incident date

Apr 2024

Mileage

Not provided

Outcome flags

None reported

Clock spring assembly had to be replaced. Horn would not work due to this. This appears to be a problem in jeeps but no recall yet on this specific model

Reported

Jun 2024

Incident date

Jun 2024

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2013 Jeep Wrangler. The contact stated while driving at approximately 40 MPH the "air bag" warning light illuminated and the horn became inoperable. The contact stated that the failure occurred at various speeds. The contact stated that the failure was intermittent. The contact was aware of an Extended Warranty for the clockspring. The contact had driven the vehicle to a local dealer however, the dealer was unable to retrieve diagnostic trouble codes associated with the clockspring, and the vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 115,000.

Reported

Jun 2024

Incident date

Aug 2023

Mileage

Not provided

Outcome flags

None reported

While I was attempting to park my jeep across the street from my grandson's school to pick him up at 3:18, as I proceeded to pull in front of the apron so I could backup to a parking spot. In the process of going forward before I got a chance to put the jeep in reverse my brakes failed, hitting a parked car in front of me. I had my jeep towed to Old Center Island Auto Service. The mechanic removed a defective power brake booster and replaced it with a new one.

Reported

May 2024

Incident date

May 2024

Mileage

Not provided

Outcome flags

Crash

Unknown

Reported

May 2024

Incident date

May 2024

Mileage

Not provided

Outcome flags

None reported

The fuel supply line that attaches to the fuel rail at the engine sprung a leak at the seam were the plastic tube is sealed together. This is a high pressure line. This resulted in fuel being sprayed directly on the hot cylinder head creating a potential fire hazard.

Reported

May 2024

Incident date

Apr 2024

Mileage

Not provided

Outcome flags

None reported

The oil pressure sensor, I was in traffic and the vehicle came to a stop with scared the hell out me and this has hall a couple of time and came to find out it was caused by the oil pressure sensor. Why this is not on recall

Reported

Apr 2024

Incident date

Jul 2023

Mileage

Not provided

Outcome flags

None reported

Michelin Defender Tire with ~90% tread exploded with no indicators or warning. VDOT repairman indicated that it had exploded from the side. Incident happened on the highway 2/24/24 going 60mph. Jeep did not observe any potholes, road debris, or curbs. I do not do off-roading. Tires had 35psi. I drive average 6000 miles a year. Tire: LT 285/70R17 121/118R dot 1b7 bf 005x 2922 load range E. Wheel: PRC 7069/AT L 13+JK 17X9 33X12.50 R17 employee from tirerack.com confirmed tire/wheel are a match. Tire is available for inspection. Will have tire shop take it off the wheel and inquire to see if they can evaluate what happened. Tire has only been inspected by VDOT employee on site of incident. No sign of warnings or dashboard light before incident until after it blew up which produced a low tire pressure indicator. Has not been reproduced or confirmed by dealer or independent service center. Safety was put in risk to driver and other drivers on highway going highway speed. Was able to control car to a stop. Jeeps are at higher risk of rolling over. Luckily nobody was hurt and no damage to vehicle other than the Tire.

Reported

Mar 2024

Incident date

Feb 2024

Mileage

Not provided

Outcome flags

None reported

Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.

Chrysler (FCA US LLC) is recalling certain model year 2011-2016 Right Hand Drive Jeep Wrangler vehicles manufactured February 16, 2010, to May 2, 2016. The clockspring assembly may become contaminated with dust and cause the air bag circuit to fail.

Risk: Failure of the air bag circuit may prevent the driver's frontal air bag from deploying in the event of a crash, increasing the risk of injury.

Remedy: Chrysler will notify owners, and dealers will replace the clockspring, wheel back cover, and column shroud, free of charge. The recall began on August 11, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S40.

Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.

Risk: An electrical short increases the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.

Chrysler Group LLC (Chrysler) is recalling certain model year 2012-2013 Jeep Wrangler vehicles equipped with a 3.6L engine and an automatic transmission and manufactured January 23, 2011, through February 23, 2013. The power steering line may contact and wear a hole in the transmission oil cooler line resulting in a loss of transmission fluid.

Risk: A loss of transmission fluid may result in a loss of transmission function which may increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the power steering return tube assembly, free of charge. The recall began on September 23, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N28.

Quadratec, Inc. is recalling certain aftermarket accessory, driver-side, Ultimate Floor Liners part numbers 14254.0301 07, 14254.0301 08, 14254.0301Q, 14254.0302 07, 14254.0302 08, 14254.0302Q, 14254.0303 07, 14254.0303 08, 14254.0303Q, 14254.0309 07, 14254.0309 08, and 14254.0309Q sold from May 1, 2012, through February 14, 2013. The liners are for use in 2007-2013 Jeep Wranglers. The anchor point for the affected floor liners may tear during use, particularly when exposed to high temperatures. The tearing may allow the floor liner to shift forward.

Risk: If the liner shifts forward it may impede the operation of the accelerator and possibly lead to unintended acceleration, which may increase the risk of a crash.

Remedy: Quadratec will notify owners and either exchange the liners or provide them with a hook guard kit to help secure the driver-side mat, free of charge. The recall began on April 4, 2013. Owners may contact Quadratec at 1-800-463-2998 or info@quadratec.com.

Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.

Risk: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.

Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.

Risk: A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.

Remedy: FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.