2012 Jeep Wrangler

The engine's cylinder head/valve train has failed internally, allowing combustion gases to enter the cooling system — confirmed via a chemical block test performed by a master automotive technician on November 29, 2024, which verified combustion gases present in the coolant. This is a widely documented defect on this engine and model year, related to valve seat erosion in the cylinder head. Symptoms first appeared in June 2018 as an unusual higher-pitched, stressed sound from the engine. Over time this progressed to recurring, confirmed misfires on cylinders 1, 2, 3, and 5 (diagnostic codes P0300, P0301, P0302, P0303, P0305) and a mixture control fault (P219B). The check engine light has intermittently stayed illuminated for months at a time, then gone off for extended periods while the same fault codes remain stored and confirmed by a diagnostic scanner — currently the light is off but the codes persist. The vehicle frequently runs rough enough that the engine must be turned off and restarted to temporarily return to closer-to-normal operation. Noticeable vibration is felt during much of this pattern. Spark plugs, ignition coils, oxygen sensors, and the PCV valve have all been inspected/replaced and ruled out as the cause on multiple occasions over more than a year, isolating the cause to the cylinder head itself. This creates a driveability and potential stalling/hesitation risk, though no crash, injury, or fire has occurred to date. The vehicle has not been formally inspected by the manufacturer, police, or an insurance representative. The affected component remains in the vehicle and is available for inspection upon request.

Reported

Jul 2026

Incident date

Nov 2024

Mileage

Not provided

Outcome flags

None reported

ABS ETC Traction control Torque management in power train and ABS I have tried to fix everything with no resolve I just drove to and from Oklahoma and the jeep is unsafe to drive

Reported

May 2026

Incident date

Dec 2025

Mileage

Not provided

Outcome flags

None reported

What happened? The vehicle was delivered to an authorized dealership for a federally mandated "Stop-Drive" Safety Recall (V01 - Passenger Airbag Inflator). During this service visit, the dealership attempted to charge an illegal $275.00 diagnostic fee for the airbag warning light, which is directly related to the recall system.  The manufacturer’s corporate office confirmed via email that as of April 23, 2026, the recall remains "OPEN" and incomplete in federal records. However, the manufacturer also issued a contradictory statement claiming the repair was "concluded" based on dealer reports.  Most critically, while in the dealer's custody for this safety repair, the vehicle was lost or released to an unauthorized party. A manufacturer-arranged "Reunite" transport service arrived on-site to return the vehicle, but the dealership could not produce it, claiming it was no longer on the lot. The dealer has failed to provide any signature, identification, or surveillance footage to prove a legal release of this "Stop-Drive" recall vehicle. The Supplemental Restraint System (SRS/Airbag). The system is not available for inspection because the dealership lost the vehicle while the recall was still marked as "OPEN" and incomplete.  How was safety put at risk? The vehicle is under a "Stop-Drive" advisory because the airbag inflator may explode, resulting in serious injury or death. By failing to perform the repair, attempting to charge for diagnosis, and losing the vehicle, the dealer and manufacturer have left a high-risk safety defect unaddressed and the vehicle's location unknown.  Has the problem been confirmed by a dealer or independent service center? Yes. The manufacturer’s own database and the NHTSA/Mopar websites confirm the recall is "Incomplete/Open". Furthermore, a third-party towing company confirmed the dealership could not locate the VIN on their lot during a scheduled pickup.

Reported

Apr 2026

Incident date

Apr 2026

Mileage

Not provided

Outcome flags

None reported

Multiple warning light activations (ABS, TCS, hill descent) diagnosed by mechanic as failed ABS module (combines electronic and hydraulic components) (PN: 68145835AE). I have been on a waiting list for a replacement part from Stellantis for almost a year. Numerous owners report online that this part is unavailable or no longer being manufactured. Stellantis has not publicly acknowledged the problem or provided a proposed solution or timeline. ABS is widely acknowledged as a key component of modern automobile safety systems. Stellantis's failure to provide replacement components for these modern vehicles places the driving public at unnecessary risk. A recommended resolution is that Stellantis provide NHTSA with a credible plan of action to begin providing replacements for this critical component (and other related part numbers).

Reported

Apr 2026

Incident date

May 2025

Mileage

Not provided

Outcome flags

None reported

THIS IS 2012 Jeep Wrangler its 14 years old and for 14 years the previous owner renewed the registration put insurance on it and it passed the emission tests despite the fact that it was recalled. Now the parts were in back order and they replaced my airbags but when the tow company went to the dealership to pick up my car the dealership wouldn’t release it This is absurd how does a 14 year old car go unnoticed that long. I had to stop driving the car for months because of this recall and the battery died you know a car can’t stay parked too long I took this recall seriously unlike Stellanis who murdered 29 people by refusing to flag these vin numbers to the DMV like the jeep I had and it’s sick how your agency has enabled this behavior truly sick

Reported

Apr 2026

Incident date

Apr 2026

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2012 Jeep Wrangler. The contact stated that while driving at 20 MPH, the check engine warning light illuminated. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The vehicle was taken to an independent mechanic, where a scan was completed, and diagnostic trouble codes for the Emissions, engine misfire, timing chain, and crank position sensor failures were displayed. The manufacturer was not contacted. The failure mileage was approximately 71,756.

Reported

Apr 2026

Incident date

Mar 2026

Mileage

Not provided

Outcome flags

None reported

My complaint is that I was sold a dangerously defective vehicle with a known, unrepaired “stop driving” airbag safety recall, was not warned about the deadly risk, and am now being told to move and tow the car in direct contradiction to official safety instructions. ### Factual background - The vehicle I purchased has a Takata‑type airbag safety recall that carries a formal “do not drive” or “stop driving” warning because the airbag can explode and kill or severely injure occupants, even in a minor crash.[1][2][3][4] - Federal safety authorities have confirmed that at least 28–29 people in the United States have been killed and more than 400 injured by exploding Takata airbag inflators.[3][4][5][1] - I received the recall notice about two months ago, but I was told the repair parts were back‑ordered, which delayed fixing the deadly defect through no fault of my own.[1][3] - During this delay, the vehicle’s battery became completely dead, and I am now being told by the recall and towing company that I must make sure the car is taken out of the garage, which would require entering and moving a vehicle I have been legally and explicitly told not to drive. ### Legal and safety concerns - Official guidance from the National Highway Traffic Safety Administration (NHTSA) and the manufacturer is that vehicles under this Takata “do not drive” recall must not be driven at all until the defective airbag is replaced, because even a minor collision can cause the inflator to explode and send metal shrapnel into the cabin.[2][4][3][1] - The instruction to move or drive the car out of the garage conflicts with this clear safety warning and effectively asks me to assume a risk that has already caused multiple deaths and serious injuries nationwide.[4][5][2][3][1] - Federal law prohibits franchised dealers from selling new vehicles with unrepaired safety recalls, and legal experts warn that selling used vehicles with undisclosed safety defects can expose sellers and dealers to

Reported

Mar 2026

Incident date

Jan 2026

Mileage

Not provided

Outcome flags

None reported

Dealer repair unavailable in local zip:99901. Require identification and shipment of part to be installed by certified mechanic or system access to report satisfactory repair has been conducted.

Reported

Mar 2026

Incident date

Mar 2026

Mileage

Not provided

Outcome flags

None reported

2012 Jeep Wrangler Sahara. Received Stop-Drive letter from Stellantis/FCA on Takata airbag recall—front airbags may explode in crash, sending metal shards. Letter says do not drive until fixed. Called hotline (833-585-0144) twice yesterday & today—no help. Dealer (Corwin Springfield) says call Chrysler. No tow arranged despite free towing advertised for Stop-Drive. No loaner or rental offered. Can't drive safely—PTSD makes group transport impossible. Have VA medical appointment March 2nd & lawyer meeting March 3rd. Can't afford rental for weeks (they say mid-March fix). Manufacturer failed to remedy timely—need tow to dealer + transport/loaner now.

Reported

Feb 2026

Incident date

Feb 2026

Mileage

Not provided

Outcome flags

None reported

ABS module failure C2200. Repair parts not available.

Reported

Feb 2026

Incident date

Oct 2025

Mileage

Not provided

Outcome flags

None reported

ABS system faile, There is no replacement part to correct the fault, and there is no replacement date, code C2200

Reported

Feb 2026

Incident date

Aug 2025

Mileage

Not provided

Outcome flags

None reported

The dash displayed multiple warning ICONS and I carried the Jeep to a mechanic. They discovered that the ABS Module, which is the anti braking system, had a fault error and needed to be replaced. After multiple attempts have found out that this particular ABS Module, OEM Part number (68145835AE) is no longer available by Jeep Chrysler and has not been available for the past few years. This means the Jeep is not safe to drive if the roads are wet or icy due to the possibility of loosing the brakes from skidding/loss of control of the vehicle.

Reported

Feb 2026

Incident date

Nov 2025

Mileage

Not provided

Outcome flags

None reported

ABS brake module (Part # 68145835AE) is a known defect on Jeep Wranglers 2012-2014. This part becomes defective, eliminating the ABS braking feature, also causing other transmission related problems. The real problem is Mopar support. Currently, NATIONALLY, this part is, and has been on back order (over 300 backorders) with no expectations of being available. I have been waiting for this part for over 6 months (no ABS) and problems with the vehicle have been escalating. This is a known problem, discussed on JEEP Forum.com, Mopar parts suppliers and among dealerships

Reported

Feb 2026

Incident date

Jan 2026

Mileage

Not provided

Outcome flags

None reported

ABS has gone out and there are no new repair parts available from Jeep

Reported

Jan 2026

Incident date

Dec 2025

Mileage

Not provided

Outcome flags

None reported

ABS module malfunction. This has been an ongoing problem for Jeep Wranglers of this year, previous and later. Jeep recalled other models for ABS module malfunctions. Being a retired auto worker am aware that same components are used on other models to defer manufacturing costs. Vehicle lot numbers do NOT isolate the problem. Bulk purchase of components should be checked per manufacturing date. I have taken my vehicle to dealer for diagnosis and they say the ABS module is bad, BUT part is on back order with no real time date ( could be 2 weeks or 6 months)for delivery. Jeep dealer wants me to pickup vehicle until part arrives. Driving vehicle under this condition could cause brakes to seize, not work at all, fire and/or a possibility of an accident! Jeep knows and has know this is a problem but never a recall on this model. Researching other Jeep owners and Jeep forums it is documented of this problem and the expense that an owner has to incur to get it resolved! Jeep has made no effort evidently to recognize this problem with the example being that parts are back ordered. Then again there is a real problem and the original part was junk but now the owner is stuck with the bill and all the safety issues because new parts are back ordered.

Reported

Jan 2026

Incident date

Jan 2026

Mileage

Not provided

Outcome flags

None reported

My Oil pump and oil sensor keep going out every 4,000 miles. I have already had to replace it once. I don’t want to have to do it again. Clearly something is causing this issue.

Reported

Jan 2026

Incident date

Aug 2024

Mileage

Not provided

Outcome flags

None reported

Having a hard time putting gas, I have to do it slowly so it can go in, the worst is when I put fuel a bit more fast it will throw gas out even if it ain't even close to half the tank.

Reported

Dec 2025

Incident date

Dec 2025

Mileage

Not provided

Outcome flags

None reported

THE 2012 Jeep 4 door Wrangler had the ABS Control Module internal error failure, this makes the car unsafe to drive. The dealer cannot get repair parts, the car is un-repaired since October 2025. Further, they cannot source the chips for the components, the make cannot provide a delivery date.(UNKNOWN when this will be rectified. Other years of this car have been recalled for this issue. This year has not yet. PLEASE Help us !)

Reported

Dec 2025

Incident date

Oct 2025

Mileage

Not provided

Outcome flags

None reported

The vehicle exhibits a persistent valvetrain ticking noise associated with the rocker/lifter/cam components of the 3.6L Pentastar V6. The engine makes a rhythmic metallic tapping at idle and during acceleration. The noise has progressively worsened, leading to rough idle and occasional misfires. This issue is documented in multiple Stellantis technical service bulletins (e.g., TSB 09-015-24 and TSB 09-011-25) which attribute the noise to hydraulic lash adjuster and cam/rocker wear. If unaddressed, the failure can cause camshaft damage, metal debris contamination, loss of power and potential engine stall, posing a safety risk. The vehicle is available for inspection. The problem has been confirmed by independent mechanics who recommend replacement of the rocker arms, lifters and camshaft to prevent catastrophic engine failure.

Reported

Oct 2025

Incident date

Oct 2025

Mileage

Not provided

Outcome flags

None reported

After replacing right front speed sensor, ABS module shows malfunction and vehicle goes into limp mode. Replacement ABS modules are unavailable from mfg.

Reported

Oct 2025

Incident date

Sep 2025

Mileage

Not provided

Outcome flags

None reported

In 2020 I bought this Jeep, within the first 3 months I had to replace the TIPM, at $950.00, now 5 years later the same problem, the TIPM is having issues again. Causing the engine to overheat. Jeep is telling me this happens, not at $950 every 5 years, I was told there was a recall initially when they were new. There has to be some sort of recourse, you just can’t sell faulty parts and say it just happens! Thank you [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Reported

Oct 2025

Incident date

Oct 2025

Mileage

Not provided

Outcome flags

None reported

I was driving through a parking lot, I made a left turn and the airbag light lit up on the dashboard.Then, a chime sounded, like a low fuel chime or door open chime. I turned off the jeep and went inside the store, I then returned to my jeep, started it back up, and drove home. Every time I’m at a low speed, and make a left turn, that same chime sound starts to chime and the airbag light flickers. A scan detected the following: B1B06(1/3)Active B1CDC(3/3)Stored B1B56(2/3)Stored I checked for a recall, but can not find anything helpful.

Reported

Oct 2025

Incident date

Oct 2025

Mileage

Not provided

Outcome flags

None reported

The vehicle exhibits a persistent valvetrain ticking noise associated with the rocker/lifter/cam components of the 3.6L Pentastar V6. The engine makes a rhythmic metallic tapping at idle and during acceleration. The noise has progressively worsened, leading to rough idle and occasional misfires. This issue is documented in multiple Stellantis technical service bulletins (e.g., TSB 09-015-24 and TSB 09-011-25) which attribute the noise to hydraulic lash adjuster and cam/rocker wear. If unaddressed, the failure can cause camshaft damage, metal debris contamination, loss of power and potential engine stall, posing a safety risk. The vehicle is available for inspection. The problem has been confirmed by independent mechanics who recommend replacement of the rocker arms, lifters and camshaft to prevent catastrophic engine failure.

Reported

Sep 2025

Incident date

Jul 2025

Mileage

Not provided

Outcome flags

None reported

Timing chain and misfire bank 1 and bank 2 crank shaft and crank sensor issues.

Reported

Aug 2025

Incident date

Aug 2025

Mileage

Not provided

Outcome flags

None reported

I am reporting a persistent and safety-relevant defect in my 2012 Jeep Wrangler with the 3.6L Pentastar engine. The vehicle is experiencing misfires on multiple cylinders, especially cylinders 1 and 5, triggering codes P0300, P0301, and P0305. These misfires result in loss of power, hesitation, and rough idle, creating serious safety concerns during acceleration or highway driving. Despite replacing spark plugs, ignition coils, the crankshaft position sensor, purge valve, and both oxygen sensors, the problem continues. The vehicle has just 83,000 miles and is currently at a certified third-party repair facility. Multiple mechanics believe the issue stems from known defects in the left (Bank 1) cylinder head or valve train components—an issue Chrysler previously acknowledged via TSBs and a 10yr/150k mile extended warranty on select VINs. I contacted Jeep Cares and requested goodwill support, but they refused to even discuss the issue because my Jeep is not at a dealership. This leaves owners like me with limited, expensive options despite being affected by a well-documented defect. Jeep forums and independent shops have seen widespread misfire problems on early 3.6L Pentastar engines, especially 2012-2013 models. I urge NHTSA to investigate this pattern of failure. The misfires impact driveability and safety, and the manufacturer has not offered sufficient resolution or consistent support to affected customers. I’m happy to provide additional information, documentation, or diagnostics.

Reported

Jun 2025

Incident date

May 2025

Mileage

Not provided

Outcome flags

None reported

The Air Bag warning light is one and won't go off.

Reported

Apr 2025

Incident date

Feb 2025

Mileage

Not provided

Outcome flags

None reported

The 2012 jeep jk wrangler has serious electrical issues. The jeep randomly stalls while driving and sometimes won’t start at all. Right before it stalls, every light on the dashboard flashes and continues to flash until the car dies. Replacing the battery doesn’t fix the issue. Numerous complaints about jeep wranglers TIPM issues have been ignored by authorities. I suppose people will have to die in a crash or spends thousands fixing the TIPM or electrical issues before getting relief.

Reported

Mar 2025

Incident date

Feb 2025

Mileage

Not provided

Outcome flags

None reported

Engine spontaneously caught fire. It had been parked for hours before it happened. Everything under the hood was totaled

Reported

Jan 2025

Incident date

Jan 2025

Mileage

Not provided

Outcome flags

Fire

Airbag light is on. Airbag sensor is out.

Reported

Jan 2025

Incident date

Jan 2025

Mileage

Not provided

Outcome flags

None reported

For more than one year I have problems with the Anti-Lock Brake System Module - Mopar part #(68145835AE). Every time I place an order it get canceled because Jeep and or the supplier have the part on back order. I wonder when the NHTSA is going to intervene with this company, before an tragedy happens and someone get kill because the Jeep don't brake like is suppose to be.

Reported

Nov 2024

Incident date

Oct 2024

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2012 Jeep Wrangler. The contact stated that while operating the vehicle the ABS, Traction Control and check engine warning lights had remained illuminated. The contact indicated that while pressing the brake pedal to stop, the brake pedal extended to the floor causing the braking distance to become extended. The vehicle was taken to the local dealer who diagnosed that the ABS module was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure but no assistance was offered. The failure mileage was 55,000.

Reported

Oct 2024

Incident date

Oct 2023

Mileage

Not provided

Outcome flags

None reported

B1B02 driver airbag squib 1 circuit open. Airbag light keeps going on and off with loud beep. Googled code saying clocking spring

Reported

Jul 2024

Incident date

Jun 2024

Mileage

Not provided

Outcome flags

None reported

Horn and all other steering wheel functions don’t work. Appears to be clock spring

Reported

Jun 2024

Incident date

May 2024

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2012 Jeep Wrangler. The contact stated that the air bag warning light had been illuminated. The vehicle was taken to an independent mechanic where it was scanned and diagnosed with DTC code: B1B02; for a failure with the driver’s side air bag. Additionally, the clock spring test had failed internally. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The vehicle was not repaired. The contact stated that after further investigation the failure was linked to NHTSA Campaign Number: 13V176000 (Air Bags) however, the VIN was not included. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 169,051.

Reported

May 2024

Incident date

May 2024

Mileage

Not provided

Outcome flags

None reported

The airbag indicator illuminated, and upon getting a diagnostic inspection from the dealership, the issue is the clock spring that is faulty. The shroud is another price required for replacement.

Reported

Jan 2024

Incident date

Jul 2023

Mileage

Not provided

Outcome flags

None reported

Report from diagnostic service 1-9-2023 cylinder head - has premature failure of valve guides and cylinder head replacement is required for repair. Yes, Jeep extended the warranty but if your vehicle did not show problems they would not fix it, but they did learn and knew at the point the seriousness of the problem and put an end date on the fix. Our vehicle outlasted their warranty by 30,000 but now is undrivable. Before anything serious happens as the driver drives on longer drives we have grounded the vehicle.

Reported

Jan 2024

Incident date

Jan 2024

Mileage

Not provided

Outcome flags

None reported

While interstate driving the vehicle dash dinged, I looked down to find the ABS, Traction Control and Emergency Brake came on. I immediately pulled off the interstate for a visual inspection of the breaks and brake fluid but did not see any glaring issues. I took the vehicle to a local shop, they read the code (C2200) and advised I needed a new ABS Control Module (Mopar Part #68145835AE). The local shop advised the Module is difficult to find, but they found one and would complete the work for $2,400.00 ($1,500 of which was for the ABS Module part). I called a local Chrystler, dodge, Jeep (Lou Fusz) dealer in O'Fallon to price verify the part. I scheduled an appointment for three weeks out. They also confirmed the code and need to replace the ABS Module for $1,500.00 ($881.00 of which was for the ABS Module part); HOWEVER, Jeep-Mopar told the dealership that the part is not available until March 20 of 2024 which would leave me with two options. 1) Sell the vehicle to the dealer; however, their offer took advantage of the ABS issue and was extremely low 2) Wait and drive the faulty vehicle Driving the Jeep with a faulty ABS Module may jeopardize critical systems, resulting in poor braking performance and potentially create a very dangerous or deadly situation. A search of this issue online in Jeep Forums has shown mass number of similar issues and others experiencing the same part deadly; meaning there are an untold number of jeeps driving with a faulty ABS Module. I pled to the NHTSA to please investigate and pressure Jeep to issue a Recall to ensure safety.

Reported

Jan 2024

Incident date

Jan 2024

Mileage

Not provided

Outcome flags

None reported

In my 2012 Jeep I had to replace the engine and catalytic converters. The engine number 3 cylinder failed due to excessive ware causing lower compression. After the engine (long block) was replaced, one of the cylinders was miss firing. This miss firing was traced to micro cracks in the plastic/composite intake manifold (original and not part of the engine replacement). Because these micro cracks changed the fuel air ratio on specific cylinders by leaning out the cylinders near the cracks this lean mixture would cause the affected cylinders to run hot that would lead to both the excessive ware on the one cylinder and would comprise the catalytic converters. Because this change in fuel air mixture was caused by the intake manifold and Jeep does not have any inspection requirements or methods for this item and even after the Jeep Dealer did a full diagnosis using their factory specified equipment the issue with the manifold was not found. My local AMMCO shop found the cracking in the manifold that was the route cause of the problem.

Reported

Jan 2024

Incident date

Jul 2023

Mileage

Not provided

Outcome flags

None reported

Jeep Wrangler 3.6 liter 90k miles lifter making loud noise. Seems you had a recall about this on the 2012 and guess I missed out

Reported

Dec 2023

Incident date

Aug 2023

Mileage

Not provided

Outcome flags

None reported

Clockspring failed causing airbag to malfunction. Jeep dealer ordered a replacement in April 2023 and still has not received the part(even though they have one in stock the manufacturer will not allow them to use and install the stock clockspring). We have been forced to drive the vehicle without an operating clockspring which creates a major safety hazard since the airbags may not deploy on impact.

Reported

Dec 2023

Incident date

Apr 2023

Mileage

Not provided

Outcome flags

None reported

Revision 6 November 2019 Dealer Service Instructions for: Customer Satisfaction Notification V41Steering Damper 2018 - 2019 (JL) JeepWrangler vehicles front suspension steering damper on about 192,000 of the vehicles may not effectively damp oscillation of the steering system, resulting in a sustained shake or shimmy in the steering wheel. I have a 2012 Wrangler with the same issue - front-end shake/shimmy. My Mechanic said to replace the stabilizer with the next level-up heavier-duty stabilizer from Mopar. Why isn't my Jeep (JK Series) included in this recall? There aren't any of these stabilizers available at Mopar or online due to exceedingly high demand from vehicle owners. This should obviously be a recall.

Reported

Nov 2023

Incident date

Nov 2023

Mileage

Not provided

Outcome flags

None reported

When the fuel vents on the top of the fuel cell get old, they are extremally brittle. Washboard roads or a pot hole can jar the fuel tank breaking the connectors that go to the emissions system and the rollover valve. If any of these plastic pieces break, there is a chance for fueling problems and effects the drivability of the vehicle. The 3 connector vent is a non-serviceable part, requiring the gas tank to be replaced. The replacement has the same plastic connectors, leaving the possibility for breakage. These connectors breaking can lead to a multitude of issues, including but not limited to fuel spills while filling, leaking fuel from hoses. I have had 2 tanks in my 2012 jku have this issue and a quick search on jeep forums will show that this is not an isolated problem.

Reported

Oct 2023

Incident date

Aug 2023

Mileage

Not provided

Outcome flags

None reported

6 days after an oil change, the temp gauge while driving went from cool to hot in under a mile and the engine temp light came on. There was coolant all over the underside of the car it was near catastrophic. I had to have it towed to the dealership for repairs. The faulty part was the oil filter adapter it was cracked by over tightening of the oil filter.

Reported

Oct 2023

Incident date

Sep 2023

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2012 Jeep Wrangler. The contact stated while driving at an undisclosed speed, the air bag warning light illuminated. The vehicle was previously repaired by the dealer under NHTSA Campaign Number: 19V018000 (Air Bags), and the contact was informed that the clockspring needed to be replaced. The vehicle was then taken to an independent mechanic, who diagnosed that the clockspring needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure but informed the contact that there was no recall associated with the VIN. The failure mileage was 167,338.

Reported

Sep 2023

Incident date

Feb 2023

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2012 Jeep Wrangler. The contact stated while driving at an undisclosed speed, the vehicle lost motive power. The vehicle was taken to an independent mechanic, who related the failure to NHTSA Campaign Number: 15V675000 (Electronic Stability Control, Service Brakes, Hydraulic). The manufacturer was made aware of the failure. The failure mileage was approximately 100,000.

Reported

Aug 2023

Incident date

Aug 2023

Mileage

Not provided

Outcome flags

None reported

The contact owns a 2012 Jeep Wrangler. The contact stated while driving 70 MPH, the front passenger’s side brakes locked up without warning. The contact was able to drive the vehicle to the residence. The vehicle was not diagnosed. The dealer was contacted and stated that the vehicle needed to be diagnosed. The contact replaced the front passenger’s side caliper however, the failure recurred. The contact also replaced the front brake lines. The manufacturer was not contacted. The failure mileage was 80,000.

Reported

Jul 2023

Incident date

Dec 2021

Mileage

Not provided

Outcome flags

None reported

There has been numerous safety recalls for this Jeep on the airbag. The airbag warning light came on and now the horn does not work.

Reported

May 2023

Incident date

May 2023

Mileage

Not provided

Outcome flags

None reported

N/A

Reported

Apr 2023

Incident date

Apr 2023

Mileage

Not provided

Outcome flags

None reported

Engine Stalls Randomly while Driving. Will crank over several times and over approx 10-15 min. of cranking(Say every 3-5min) vehicle will and will restart. No check engine lights and no warning. The loss of power can be dangerous since brake and steering assist require engine to be running. Vehicle will be fine for several days local commute and problem will recur without warning, usually on longer commute. Vehicle is unsafe and unpredictable.

Reported

Apr 2023

Incident date

Apr 2023

Mileage

Not provided

Outcome flags

None reported

I noticed that the air bag light came in about 6-12 months ago. I am very concerned because, my Jeep is in excellent shape, however, I transport my 94 yo mom around, so this really bothers me. I have seen several recalls regarding air bags in my model, so I wanted to see if this would be part of one of the recalls. I had my mechanic review and to replace would cost me about $800, which I do not have. If this is due to a failure on Jeeps part, I would like this taken care of.

Reported

Feb 2023

Incident date

Jun 2022

Mileage

Not provided

Outcome flags

None reported

Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.

Chrysler (FCA US LLC) is recalling certain model year 2011-2016 Right Hand Drive Jeep Wrangler vehicles manufactured February 16, 2010, to May 2, 2016. The clockspring assembly may become contaminated with dust and cause the air bag circuit to fail.

Risk: Failure of the air bag circuit may prevent the driver's frontal air bag from deploying in the event of a crash, increasing the risk of injury.

Remedy: Chrysler will notify owners, and dealers will replace the clockspring, wheel back cover, and column shroud, free of charge. The recall began on August 11, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S40.

Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.

Risk: An electrical short increases the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 Jeep Wrangler right-hand drive vehicles manufactured February 1, 2007, through October 10, 2011. The affected vehicles have airbag clockspring assemblies that could experience broken airbag circuits.

Risk: In the event of a crash necessitating airbag deployment, a broken electrical circuit in the airbag clockspring wiring assembly can lead to non-deployment of the driver-side frontal airbag and will not be able to properly protect the driver, increasing the risk of injuries.

Remedy: Chrysler will notify owners, and dealers will replace the clockspring and add a steering wheel dust shield, free of charge. The recall began on June 10, 2013. Owners may contact Chrysler at 1-800-247-9753. This recall supercedes NHTSA recall 11V-528. Chrysler's recall campaign number is M31.

Chrysler Group LLC (Chrysler) is recalling certain model year 2012-2013 Jeep Wrangler vehicles equipped with a 3.6L engine and an automatic transmission and manufactured January 23, 2011, through February 23, 2013. The power steering line may contact and wear a hole in the transmission oil cooler line resulting in a loss of transmission fluid.

Risk: A loss of transmission fluid may result in a loss of transmission function which may increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the power steering return tube assembly, free of charge. The recall began on September 23, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N28.

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2012 RIGHT HAND DRIVE (RHD) JEEP WRANGLER VEHICLES MANUFACTURED FROM FEBRUARY 1, 2007, THROUGH OCTOBER 10, 2011. SOME VEHICLES MAY BE EQUIPPED WITH DRIVER'S AIRBAG CLOCKSPRING ASSEMBLIES THAT COULD EXPERIENCE A COMPROMISED AIRBAG CIRCUIT RESULTING IN AN AIRBAG LAMP ILLUMINATION, WHICH INDICATES THAT THE AIRBAG MAY NOT DEPLOY.

Risk: A BROKEN ELECTRICAL CIRCUIT IN THE AIRBAG CLOCKSPRING WIRING ASSEMBLY CAN LEAD TO NON-DEPLOYMENT OF THE DRIVER FRONTAL AIRBAG AND WILL NOT BE ABLE TO PROPERLY PROTECT THE DRIVER IN THE EVENT OF A CRASH, INCREASING THE RISK OF INJURIES.

Remedy: CHRYSLER WILL NOTIFY OWNERS AND REMEDY THE VEHICLES AS NECESSARY FREE OF CHARGE. CHRYSLER WILL MAIL TO OWNERS AN INTERIM NOTIFICATION DURING MARCH 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Quadratec, Inc. is recalling certain aftermarket accessory, driver-side, Ultimate Floor Liners part numbers 14254.0301 07, 14254.0301 08, 14254.0301Q, 14254.0302 07, 14254.0302 08, 14254.0302Q, 14254.0303 07, 14254.0303 08, 14254.0303Q, 14254.0309 07, 14254.0309 08, and 14254.0309Q sold from May 1, 2012, through February 14, 2013. The liners are for use in 2007-2013 Jeep Wranglers. The anchor point for the affected floor liners may tear during use, particularly when exposed to high temperatures. The tearing may allow the floor liner to shift forward.

Risk: If the liner shifts forward it may impede the operation of the accelerator and possibly lead to unintended acceleration, which may increase the risk of a crash.

Remedy: Quadratec will notify owners and either exchange the liners or provide them with a hook guard kit to help secure the driver-side mat, free of charge. The recall began on April 4, 2013. Owners may contact Quadratec at 1-800-463-2998 or info@quadratec.com.

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Risk: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.

Risk: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.

Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.

Risk: A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.

Remedy: FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.