2021 Mazda Mazda3 · keep 3 yr

The records describe a problem worth checking before purchase.

“Spontaneous loss of power while driving on highway. Check engine light came on. Speed limited by car. Continues to vibrate especially at idle from cold start. Code P0304 intermittently popping up.”

The records describe a problem worth checking before purchase.

“The thermostat malfunctioned on this vehicle, resulting in the thermostat remaining open and providing excess coolant to the engine, which in turn damaged internal components of the engine (compromises safety), decreased fuel economy, increased emissions (compromised safety), and decreased the life of the engine within the vehicle. It is available for inspection upon request. The vehicle has been inspected by an independent mechanic and will be inspected by the Mazda dealership in 7 days. There were no prior warnings until the engine malfunction notice appeared, the vehicle began to make jolts and stuttering sounds, and the temperature gauge within the vehicle failed to rise to optimal range. As this occurred while the vehicle was in use (safety concern), though I was pushing the gas there would be delayed response due to improper temperature, which increased the risk for an accident to occur.”

The records describe a problem worth checking before purchase.

“The contact owns a 2021 Mazda Mazda3. The contact received notification of an unknown Class Action Lawsuit Number however, the part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.”

The records describe a problem worth checking before purchase.

“Low oil light - car is burning oil and only has 11,400 miles. Approx 3/4 to 1 quart missing...”

The records describe a problem worth checking before purchase.

“Driving on a remote highway in northern WI and low oil light illuminated, 1000 miles before oil change was due with less than 10k miles on the vehicle. Made it to a gas station and oil was a quart low. Vehicle burns over a quart every oil change interval, since this has been occurring since day 1 it is likely going to cause premature engine failure which would be a safety issue.”

The records describe a problem worth checking before purchase.

“Received Low Oil Level warning ... checked engine oil and it is under the minimum level on the dip stick. Car has only 11,725 miles”

The records describe a possible crash, fire, injury, or loss of control.

“My rear differential case cracked, anytime the four wheel drive system was engaged the entire drivetrain would lock up. Luckily we were only on side roads so going less than 30 mph if we had been on the highway when this happened we could have been in an accident or lost control. The dealer did confirm the problem and it was fixed under an extended warranty. There was no warning just all of a sudden a loud bang and all the wheels locked up. I have a copy of the video inspection done at the dealer if there's anyway to send that. I can get a copy of the repair invoice if needed”

The records describe a possible crash, fire, injury, or loss of control.

“I was driving when all the sudden there was a loud bang sound. The differential housing cracked. The when awd is demanded the rear diff was was locking up instead of engaging. Luckily we were just on city streets and not on the highway as this rear wheel locking up could cause a crash. Mazda wasn't very helpful with the replacement. Luckily I had a aftermarket warranty but it only paid for a used replacement, which is also failing. I have read lots of stories of this rear differential failure across all types of Mazda's from this era and really wish they would do the correct thing and resolve the problem.”

The records describe a possible crash, fire, injury, or loss of control.

“Radiators are failing 3 years after the warranty period. Its leading to coolant lost and perhaps overheating the engine.”

The records describe a possible crash, fire, injury, or loss of control.

“Mazda North American Operations (Mazda) is recalling certain 2021 Mazda3 and CX-30 vehicles. Air may suddenly leak from the tire air valve. A sudden air leak from the tire air valve may cause a loss of vehicle control while driving, increasing the risk of a crash. Mazda will notify owners, and dealers will replace all four tire air valves with new parts, free of charge. The recall began April 6, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4721B.”

The records describe a problem worth checking before purchase.

“SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. ”

The records describe a problem worth checking before purchase.

“SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.”

The records describe a problem worth checking before purchase.

“SSPC5 - SPECIAL SERVICE PROGRAM - 2019-2021 MAZDA3 AND 2020-2021 CX-30 - CONTROL UNITS REPROGRAMMING Concern 1: Mazda3 and CX-30 – Battery concern On the subject vehicles, the CCU (climate control unit) and BCM (body control module) may not go into sleep mode even after the ignition is switched OFF or may take time to go into sleep mode. An electric current may continue to flow, allowing the battery to discharge and run out if the vehicle is left unused for a certain time. Causal factor: Inappropriate control program of CCU and BCM. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules. Concern 2: Mazda3 and CX-30 - MRCC concern: On the subject vehicles, the responsiveness when driving following a preceding car using the MRCC (Mazda Radar Cruise Control) system is designed to high response. Some drivers may feel the acceleration and deceleration jerk when using MRCC somewhat uncomfortable. The product update has been incorporated into mass-production Mazda3 and CX-30 vehicles, and acceleration and deceleration has been made more natural by changing controls to be closer to human expectation. The similar update will be made on the subject vehicles produced prior to the product update under this SSP. * MRCC: Mazda Radar Cruise Control (MRCC) uses a millimeter wave radar to judge the relative speed and distance to the car ahead and automatically controls vehicle speed. Working within a set speed range, MRCC automatically adjusts and maintains a safe following distance from the car in front. Concern 3: CX-30 - Theft-Deterrent System concern On the subject vehicles, the theft-deterrent system may not recognize correctly the open/close state of power liftgate, which may allow the theft-deterrent system to activate wrongly when the liftgate is opened by pressing the power liftgate switch. Causal factor: Inappropriate control program of BCM and LFU. Update to BCM will also update the IC, DOOR_ESU_D, DOOR_ESU_P, ESU modules.”

The records describe a problem worth checking before purchase.

“On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.”

The records describe a problem worth checking before purchase.

“On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.”

The records describe a problem worth checking before purchase.

“On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.”

The records describe a problem worth checking before purchase.

“Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat installed inside of the suspected coolant control valve on certain 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6 and 2020-2023 CX-30 vehicles. The warranty coverage for an applicable repair has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. If you are a recipient of this notice, your vehicle is included in this warranty extension program. What is the problem? On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.”

The records describe a problem worth checking before purchase.

“Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat installed inside of the suspected coolant control valve on certain 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6 and 2020-2023 CX-30 vehicles. The warranty coverage for an applicable repair has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. If you are a recipient of this notice, your vehicle is included in this warranty extension program. What is the problem? On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.”

The records describe a problem worth checking before purchase.

“Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat installed inside of the suspected coolant control valve on certain 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6 and 2020-2023 CX-30 vehicles. The warranty coverage for an applicable repair has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. If you are a recipient of this notice, your vehicle is included in this warranty extension program. What is the problem? On certain subject vehicles, the check engine light is illuminated with diagnostic trouble code (DTC) P0126, due to the fail-safe thermostat being stuck open. Additionally, you may notice one or more of the following symptoms: -Engine takes longer to warm up. -Engine temperature gauge fluctuates. -Low coolant temperature indicator (blue) light stays on longer or turns on while driving. -Poor heater performance, especially at idle. This warranty extension program applies only to the replacement of fail-safe thermostat of the vehicle exhibiting the concerns mentioned above. If the check engine light illumination is determined to be unrelated to the fail-safe thermostat being stuck open, the inspection and repair are not covered under this program.”

The records describe a problem worth checking before purchase.

“SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs. ”

The records describe a problem worth checking before purchase.

“SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs. ”

The records describe a problem worth checking before purchase.

“SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.”

The records describe a problem worth checking before purchase.

“Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change. ”

The records describe a problem worth checking before purchase.

“Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change. ”

The records describe a problem worth checking before purchase.

“Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change. ”